A stochastic model for burn‐in procedures in accelerated environment

Burn‐in procedure is a manufacturing technique that is intended to eliminate early failures of system or product. Burning‐in a component or system means to subject it to a period of use prior to being used in field. Generally, burn‐in is considered expensive and so the length of burn‐in is typically limited. Thus, burn‐in is most often accomplished in an accelerated environment in order to shorten the burn‐in process. A new failure rate model for an accelerated burn‐in procedure, which incorporates the accelerated ageing process induced by the accelerated environmental stress, is proposed. Under a more general assumption on the shape of failure rate function of products, which includes the traditional bathtub‐shaped failure rate function as a special case, upper bounds for optimal burn‐in time will be derived. A numerical example will also be given for illustration. © 2006 Wiley Periodicals, Inc. Naval Research Logistics, 2006     

基于退化速率跟踪粒子滤波的剩余使用寿命预测框架

毋庸置疑,剩余使用寿命预测对于设备的健康管理越来越重要。近年来粒子滤波方法被越来越多地应用到设备寿命预测技术当中,这是因为粒子滤波方法能更好的解决非线性非高斯系统滤波问题,而且能够获得不确定度信息。但该方法的预测性能却过度依赖于预测模型,并且对于模型参数的初始分布也比较敏感,这在一定程度上限制了粒子滤波预测方法的进一步发展。本文针对基本粒子滤波预测方法的不足,提出了一种基于退化速率跟踪粒子滤波的通用预测框架,以历史观测数据的退化速率统计规律作为指导来跟踪目标数据的退化速率,实现对粒子滤波预测方法的简化。并将该方法用于轴承和锂离子电池的剩余使用寿命预测,验证了方法的有效性。     

A case study in bio-inspired engineering design: defense applications of exoskeletal sensors

As part of a bio-inspired design process, the authors examine exoskeletal sensors found in insects and their potential application to armor and hardened buildings. In this way, the outer hardening of a structure or vehicle would not limit the ability of occupants to arrive at an actionable picture of the outer environment. To this end, various sensor modalities employed by insects are compared and contrasted with their current human-engineered equivalents. In several sensing modalities, biosensors perform better, are smaller, and more energy efficient than human-engineered equivalents. They note that biological designs tend to employ non-linear response to signal amplitude and respond with heightened sensitivity over a greater dynamic range of signals than human-engineered sensors. The insect biological sensors have structural and mechanical innovations that preserve the protective capacity of the exoskeleton.     

基于自适应阈值的FAST特征点提取算法

FAST特征提取算法阈值选取固定,因此不能满足不同图像的特征点抽取要求,并且提取的结果存在着多个特征点块的现象。针对这些缺陷,首先采用动态全局阈值对原始灰度图像进行初步提取得到候选特征点,然后采取动态局部阈值和非极大值抑制法进一步对候选特征点进行筛选,从而达到自适应选取阈值和抑制多个特征点块的目的。实验表明,改进后的算法稳定性高,对不同光照和对比度情况下有一定的适应能力,并且运算量相对比于其他一些特征提取算法要小得多,满足实时应用的要求。     

Thermal hazard assessment of TKX-50-based melt-cast explosive

In the present study, thermal hazards of TNT and DNAN used as the molten binder in TKX-50-based melt-cast explosives were comparatively studied through accelerating rate calorimeter (ARC) and Cook-off experiments. Two kinds of ARC operation modes were performed to investigate the thermal safety performance under adiabatic conditions (HWS mode) and constant heating (CHR mode). The obtained results demonstrated that at both heating modes, DNAN/TKX-50 outperformed TNT/TKX-50 from the thermal safety point of view. However, the sensitivity to heat of the samples was reverse because of the different heating modes. In addition, the results of thermal hazard assessment obtained from the cook-off experiment complied with ARC analysis which indicated the molten binder TNT replaced by DNAN would reduce the hazard of the TKX-50 melt cast explosive. Furthermore, the results of cook-off experiments also showed that DNAN/TKX-50 outperformed TNT/TKX-50 from the aspect of thermal stability, which was consistent with the result of CHR mode because of the similar heating process.     

Formation of adiabatic shearing band for high-strength Ti-5553 alloy: A dramatic thermoplastic microstructural evolution

By using split Hopkinson pressure bar, optical microscopy and electronic microscopy, we investigate the influence of initial microstructures on the adiabatic shear behavior of high-strength Ti–5Al–5V–5Mo–3Cr (Ti-5553) alloy with lamellar microstructure and bimodal microstructure. Lamellar alloy tends to form adiabatic shearing band (ASB) at low compression strain, while bimodal alloy is considerably ASB-resistant. Comparing with the initial microstructure of Ti-5553 alloy, we find that the microstructure of the ASB changes dramatically. Adiabatic shear of lamellar Ti-5553 alloy not only results in the formation of recrystallized β nano-grains within the ASB, but also leads to the chemical redistribution of the alloying elements such as Al, V, Cr and Mo. As a result, the alloying elements distribute evenly in the ASB. In contrast, the dramatic adiabatic shear of bimodal alloy might give rise to the complete lamination of the globular primary α grain and the equiaxial prior β grain, which is accompanied by the dynamic recrystallization of α lamellae and β lamellae. As a result, ASB of bimodal alloy is composed of α/β nano-multilayers. Chemical redistribution does not occur in ASB of bimodal alloy. Bimodal Ti-5553 alloy should be a promising candidate for high performance armors with high mass efficiency due to the processes high dynamic flow stress and excellent ASB-resistance.     

Reliability sensitivity analysis based on multi-hyperplane combination method

For a nonlinear limit state function, the first-order reliability method (FORM) may cause large errors in the computation of not only the reliability index or failure probability but also the reliability sensitivity. In order to obtain more the accurate results of the reliability sensitivity analysis, a number of hyperplanes are built near the design point by first-order Tayler series expansion, which replace the known nonlinear limit state hypersurface, and an equivalent computational method is utilized to construct an equivalent hyperplane of the obtained hyperplanes. And the reliability sensitivities can be estimated more accurately by the derived equations based on the equivalent hyperplane. An example shows that the method is effective and feasible.     

基于敏感性分析的DF化学动力学模型的简化

基于两种燃料体系下的DF详细化学反应动力学模型,利用敏感性分析的方法,分别提出了相应的简化反应机理.简化过程中发现,仅考虑DF“冷反应”泵浦过程,忽略掉高振动激发态,忽略掉D2和DF分子的离解复合反应对整个系统影响不大.DF分子之间以及DF与D、D2、HF之间的能量转移反应具有较高的敏感性.简化机理在有效概括DF化学反...     

切向空气气流对激光辐照碳纤维复合材料的影响

实验研究了靶材表面存在和不存在切向空气气流时,975nm连续激光对碳纤维增强树脂基复合材料的辐照效应,发现切向气流的加载有利于激光对碳纤维复合材料的破坏.从理论上对激光辐照下碳纤维复合材料的破坏机理进行了初步分析,基于碳的氧化特性和氧化反应机理,推导了碳纤维的氧化速率方程.采用改进的光滑粒子方法,对激光辐照下复合材料树...